Klüber WOLFRACOAT C FLUID High-temperature lubricating compound 20L

WOLFRACOAT C FLUID High-temperature lubricating compound | N° 099118WOLFRACOAT C FLUID is a viscous high-temperature release agent and lubricating compound based on a mineral and ester oil mixture. It contains solid lubricants, metal pigments and an inorganic thickener.The base fluid starts to evaporate at approx. 200°C, leaving a solid lubricant film, which separates frictional surfaces (dry lubrication).Temperature range: -25°C to +1050°C Volume: 20 L canister Also available in: 1 L canister, 5 L canister, 200 L barrelBenefits for your applicationVery good corrosion protection → increased component lifetimeReady-for-use → just mix vigorouslyLow consumption → low costs, high efficiencyEasy application → reduces maintenance timeEasier to mix in smaller canisters → less effort requiredNo part-used stock → the 5 l pack size matches the tank of the Klübermatic KD spray pumpApplicationsWOLFRACOAT C FLUID was developed as a lubricating compound for surfaces subject to high thermal loads, as e.g. in rotary kilns in the base material industry (chemical industry, cement, ore processing, etc.) between the inner surfaces of the tyres and the kiln shell’s slide elements as well as the running surfaces of the axial supports.WOLFRACOAT C FLUID is also suitable for the lubrication of pouring ladles used in the steel industry, and could also be used as a screw compound for high-temperature bolt and screw connections. Application notesWOLFRACOAT C FLUID is usually applied to the area between the tyre and the kiln shell with the Klübermatic KD manual spray jet equipment (other commercially available spray devices can also be used). In other cases the product can also be applied by brush. Each tyre should be relubricated once a week with 2-3 litres of WOLFRACOAT C FLUID according to the tyre width. It is important to ensure relative motion between the tyre and the kiln shell. We recommend reference to the relative motion value stated by the OEM (between 10 and 30 mm)NOTE: Always shake WOLFRACOAT C FLUID vigorously prior to application, as the solid lubricants tend to settle out during storage. Without agitation, the spray jet would be filled only with the oil component, which would not provide dry lubrication following evaporation. Additionally, the oil component has an auto-ignition point of approx. 370 °C which may constitute a riskTechnical specifications Manufacturer number 0991180766 Solid lubricants  approx. 16 % by weight Colour space grey Texture  homogeneous , very viscous Service temperature, lower limit -25 °C Service temperature, upper limit 1050 °C Density, Klüber method: PN 024, 20°C approx. 1.03 g/cm³ Worked penetration, Klein, 25°C, lower limit 800 0.1 mm Worked penetration, Klein, 25°C, upper limit 900 0.1 mm Minimum shelf life from the date of manufacture – in a dry, frost-free place and in the unopened original container, approx. 24 monthsHazard Statements (CLP)Signal word: Warning.Hazard Statements (H-phrases)H410: Very toxic to aquatic life with long-lasting effects.Precautionary Statements (P-phrases)Prevention:P273: Avoid release to the environment.Response:P391: Collect spillage.Other Relevant InformationThis substance/mixture does not contain components in concentrations of 0.1% or higher that are classified as persistent, bioaccumulative, and toxic (PBT) or very persistent and very bioaccumulative (vPvB).This substance/mixture does not contain components classified as endocrine-disrupting according to REACH Article 57(f) or the Commission Delegated Regulation (EU) 2017/2100 or (EU) 2018/605 in quantities of 0.1% or more.×Hazardous materials. The forwarding charges may be raised, if shipping to: DE, AT, NL, GB, CH, CZ, IT, ES, FI, NO, BE, IE, RO, PL, FR, PT, LU, DK, LI, GR, SE, SK, BG, SI, CA, LT, EE, LV, HR, SA,  Information on product safety (Manufacturer, Contact)KLÜBER LUBRICATION MÜNCHEN GMBH & CO. KG, Geisenhausenerstraße 7, 81379 München, GERMANY, +49 89 7876 0, , www.klueber.com