Klübersynth EG 4-150 Synthetic high-performance gear oil 1 Litre

Synthetic high-performance gear oilKlübersynth EG 4 is a fully synthetic high-performance gear oil based on polyalphaolefin satisfying the requirements of many gears.Klübersynth EG 4 offers a high scuffing strength of API GL-4. Gears are sufficiently protected against scuffing even at extremely high peak loads, vibrations or oscillations. The good wear protection of the gear components ensures that their calculated service life is achieved, leading to lower maintenance and repair costs.Klübersynth EG 4 offers a much longer service life than mineral oils due to the excellent ageing and oxidation resistance of the selected raw materials; thus service intervals can be extended and maintenance costs reduced. The product’s low foaming tendency and anti-corrosive properties enable problem-free gear operation. Klübersynth EG 4 is neutral towards most sealing materials such as NBR or FKM. Oil leakage leading to contamination is prevented. It also shows good demulsifying behaviour.The good viscosity-temperature behaviour supports the formation of a sufficient lubricant film across a wide service temperature range. Therefore, a single viscosity grade can cover both low and high temperatures in many applications. The optimised friction behaviour enabled by the carefullyselected base oils reduces power loss and improves gear efficiency.By using Klübersynth EG 4 you can benefit from a number of advantages that will help you save costs easily and efficiently. We look forward to hearing from you.Content: 390ml tinAvailable in 390ml tin, 19l canisterBenefits:High scuffing protectionGood wear protectionExcellent ageing and oxidation resistanceWide service temperature range due to good viscosity-temperature behaviourLow foaming tendencyEnergy savings due to optimised friction behaviourVery good corrosion protectionApplication:Klübersynth EG 4 was especially developed for the lubrication of heavily loaded spur, bevel and planetary gears. It can also be used for the lubrication of worm gears.Klüberoil EG 4 can also be selected for the lubrication of plain and rolling bearings, all kinds of toothed couplings, chains, guideways, joints, spindles and pumps.Application notes:Klübersynth EG 4 can be used for immersion, immersion circulation and injection lubrication.The use of drip-feed oilers, brushes, oil cans or suitable automatic lubricating systems is also possible. When using automatic lubricating systems, please note the manufacturer’s instructions regarding the maximum permissible viscosity. The low-viscosity varieties are also used for oil mist lubrication.Klübersynth EG 4 is miscible with mineral oils. However, for the Klübersynth EG 4 oil to deliver its full performance, any residues of a previously used mineral oil should not exceed 5 % in quantity.For use at permanent temperatures of 80 °C max., seals made of NBR may be used. For higher temperatures, seals made of FKM should be chosen. It should be noted that elastomers from one or several manufacturers can behave differently; therefore tests should be performed.For checking the contact pattern during running-in, the inspection paint Klübertop P 39-462 Spray (Art. No. 081295) can be used. Product data: Article number12220ISO viscosity grade, DIN ISO 3448150AGMA number4 EPLower service temperature-35 °C / -31 °FUpper service temperature140 °C / 284 °FDensity, DIN 51757, 20 °Capprox. 0,87 g/cm³Kinematic viscosity, DIN 51562 pt. 01/ASTM D-445/ASTM D 7042, 40 °C approx. 150 mm²/sKinematic viscosity, DIN 51562 pt. 01/ASTM D-445/ASTM D 7042, 100 °Capprox. 18 mm²/sViscosity index, DIN ISO 2909>= 130Pour point, DIN ISO 3016<= -39 °CFlash point, DIN EN ISO 2592, Cleveland, open-cup apparatus>= 200 °CFoam test, ASTM-D 892, ISO 6247, sequence I/24 °C<= 100/10 mlFoam test, ASTM-D 892, ISO 6247, sequence II/ 93.5 °C<= 100/10 mlFoam test, ASTM D 892, ISO 6247, sequence III/24°C<= 100/10 mlFZG scuffing test, DIN ISO 14635-1, A/8.3/90, scuffing load stage>= 14FZG scuffing test, based on DIN ISO 14635-1, A/16.6/90, scuffing load stage>= 12API scuffing load capacityAPI GL 4FAG FE8 rolling bearing test, DIN 51819-3, D 7,5/80-80, wear of rolling element<= 30 mgFAG FE8 rolling bearing test, DIN 51819-3, D 7,5/80-80, wear of cage<= 200 mgMinimum shelf life from the date of manufacture - in a dry, frost-free place and in the unopened original container, approx.60 months