Klübersynth GH 6-80 High performance gear oil 20L

Synthetic high-performance gear and high-temperature oil with KlüberComp Lube TechnologyKlübersynth GH 6 is a synthetic high-performance gear and high-temperature oil based on polyglycol satisfying the growing requirements and increasing power density of modern gears. It includes KlüberComp Lube Technology*, i.e. it is based onespecially high-grade raw materials and advanced additives, enabling maximum performance in the lubrication of all gear components.Klübersynth GH 6 clearly exceeds CLP requirements according to DIN 51517-3. Corresponding gears can be switched to Klübersynth GH 6 without prior consultation with the gear manufacturer provided the general application notes are observed.Klübersynth GH 6 offers high scuffing load capacity of API GL-5 if ISO VG 220 or higher is selected. Gears are sufficiently protected against scuffing even at extremely high peak loads, vibrations or oscillations, or if no running-in was performed. The excellent wear protection of both gears and rolling bearings ensures that the service life calculated for the lubricatedcomponents is achieved, leading to lower maintenance and repair costs.The oil’s high micropitting resistance of GFT ≥ 10 according to FVA 54/7 (tested at 90, 60 and 40 °C) offerssufficient protection to gears that are subject to high loads and would normally be susceptible to this type of damage.Size: 5l canisterAvailable in 5l canister, 20l canisterBenefitsHigh scuffing protectionExcellent wear protection for gears and rolling bearingsGood shear stability for reliable lubricant film formationHigh micropitting resistanceOptimised for the lubrication of worm gearsExcellent ageing and oxidation resistanceWide service temperature range due to good viscosity-temperature behaviourLow foaming tendencyEnergy savings due to optimised friction behaviourGood elastomer compatibilityApprovals by numerous gear OEMsApplicationKlübersynth GH 6 oil was especially developed for the lubrication of worm gears with steel/bronze or steel/grey cast iron pairings.Klübersynth GH 6 oil is also used for the lubrication of bevel and spur gears, rolling and plain bearings as well as all types of toothed couplings, especially when exposed to high temperatures.It can also be used for the lubrication of lifting, drive and transport chains.Application notes:Klübersynth GH 6 can be applied by means of immersion, immersion circulation or injection. The use of drip-feed oilers, brushes, oil cans or suitable automatic lubricating systems is also possible. When using automatic lubricating systems, please note the manufacturer’s instructions regarding the maximum permissible viscosity. The low-viscosity varieties arealso used for oil mist lubrication.Klübersynth GH 6 is not miscible with mineral oil or synthetic hydrocarbons. Prior to switchover, lubrication points should be cleaned, or gears or enclosed lubrication systems be flushed with the Klübersynth GH 6 oil to be used.Klübersynth GH 6 oil is neutral towards virtually all nonferrous  metals. Product data:Article number12158Marking acc. to DIN 51502CLP PG 68Classification acc. to ISO 12925-1CKC 68Lower service temperature-40 °C / -40 °FUpper service temperature160 °C / 320 °FISO viscosity grade, DIN ISO 344868Density, based on DIN 51757) at 15 °Capprox.  1 040 kg/m³Kinematic viscosity, DIN 51562 pt. 01/ASTM D-445/ASTM D 7042, 20 °Capprox.  205 mm²/sKinematic viscosity, DIN 51562 pt. 01/ASTM D-445/ASTM D 7042, 40 °Capprox. 68 mm²/sKinematic viscosity, DIN 51562 pt. 01/ASTM D-445/ASTM D 7042, 100 °Capprox. 14,5 mm²/sViscosity index, DIN ISO 2909>= 190Flash point, DIN EN ISO 2592, Cleveland, open-cup apparatus>= 220 °CPour point, DIN ISO 3016<= -40 °CFoam test, ASTM-D 892, ISO 6247, sequence I/24 °C<= 100/10 mlFoam test, ASTM-D 892, ISO 6247, sequence II/ 93.5 °C<= 100/10 mlFoam test, ASTM D 892, ISO 6247, sequence III/24°C<= 100/10 mlCopper corrosion, DIN EN ISO 2160, 24 h/100°C1 - 100 corrosion degreeAnticorrosive properties on steel, DIN ISO 7120, method A, steel, 24 h/60 °Cno rust corrosion degreeAgeing properties, ASTM D 2893, increase in viscosity<= 6 %FZG scuffing test, based on DIN ISO 14635-1, A/16.6/90, scuffing load stage>= 12FZG scuffing test, DIN ISO 14635-1, A/8.3/90, scuffing load stage>= 14FAG FE8 rolling bearing test, DIN 51819-3, D 7,5/80-80, wear of rolling element< 5 mgFAG FE8 rolling bearing test, DIN 51819-3, D 7,5/80-80, wear of cage<= 200 mgMinimum shelf life from the date of manufacture - in a dry, frost-free place and in the unopened original container, approx.36 months