Delo-Photobond 4436 UV-curing acrylate adhesive tension-equalizing 1kg

Basemodified acrylateOne-component, solvent-freeUseSpecifically developed for interior visual bondings, e. g., bonding of prisms for beamers-   high transparency and permanent light fastnessVery good  capillary propertiesEasy processing at room lighting is possibleThe cured product is normally used in a temperature range of -40 °C to +120 °C; depending onthe application, other limits may be more reasonableCompliant with RoHS directive 2015/863/EUProcessingThe adhesive is supplied ready for use; in case of cool storage, it must be ensured that thecontainer is conditioned to room temperature before useThe containers are conditioned at room temperature (+18 °C to +25 °C); the conditioning time isapprox. 0.5 h for containers up to 50 ml and approx. 4 h for containers up to 1,000 ml; additional heat addition is not allowed-   the adhesive can be applied by dispensingThe surfaces to be bonded must be dry as well as free of dust, grease and other contaminationsDispensing valves and product-bearing elements must be carefully cleaned before use,residues of other products must be completely removed; DELOTHEN EP as well as acetone,isopropanol or a mixture of both are recommended to remove DELO-PHOTOBOND residuesFor further information please refer to our instructions for use DELO-PHOTOBOND and thebrochure “Light Curing”CuringCuring with UV light in a wavelength range from 320 to 400 nm. DELOLUX LED curing lampsare especially suitable as per the chart below. All standard DELOLUX HID discharge lamps arealso suitable-   increased intensities shorten the required irradiation time, lower intensities prolong it.Size: 50g bottleTechnical specificationsTension-equalizingSuitable lamp types: LED 365 nm, LED 400 nm, UVAColor in uncured condition colorlessTransparency transparentColor in cured condition in 0.1 mm layer thickness colorlessColor in cured condition in 1 mm layer thickness colorlessDensity 1.0 g/cm³Viscosity (Liquid | Viscosimeter): 350 mPa·sStorage life in unopened original container (at 0 °C to +10 °C ): 12 monthsHazards Information (CLP)Signal word: WarningHazard statements (H phrases) H315: Causes skin irritation. H317: May cause an allergic skin reaction. H319: Causes serious eye irritation. H335: May cause respiratory irritation. H400: Very toxic to aquatic life. H410: Very toxic to aquatic life with long-lasting effects.Precautionary statements (P phrases)Prevention: P280: Wear protective gloves. Recommended: Viton® fluor rubber (1-4 hours breakthrough time). For short-term exposure (< 15 minutes): nitrile gloves. P280: Wear eye or face protection. P273: Avoid release to the environment. P261: Avoid breathing vapors. P264: Wash hands thoroughly after handling.Response: P304+P340: IF INHALED: Remove person to fresh air and keep comfortable for breathing. If unwell, consult a poison center or doctor. P362+P364: Take off contaminated clothing and wash before reuse. P302+P352: IF ON SKIN: Wash with plenty of water. P333+P313: If skin irritation or rash occurs: Get medical advice/attention. P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P337+P313: If eye irritation persists: Get medical advice/attention.Storage and disposal P403: Store in a well-ventilated place. P233: Keep container tightly closed. P501: Dispose of contents/container in accordance with local/regional/national/international regulations.Other relevant information The product is classified as hazardous according to Regulation (EC) No 1272/2008. The mixture contains no substances assessed as PBT or vPvB.×Hazardous materials. The forwarding charges may be raised, if shipping to: DE, AT, NL, GB, CH, CZ, IT, ES, FI, NO, BE, IE, RO, PL, FR, PT, LU, DK, LI, GR, SE, SK, BG, SI, CA, LT, EE, LV, HR, SA,  Information on product safety (Manufacturer, Contact)DELO Industrie Klebstoffe GmbH & Co. KGaA, DELO-Allee 1, 86949 Windach, GERMANY, +49 8193 9900-0, , www.delo.de